To connect the back camera, connect the camera with transmitter, then connect the power cables to 12V power source (for example from backup light). W celu podłączenia kamery cofania należy połączyć kamerę z transmiterem, a następnie przewody zasilające podłączyć do zasilania 12V, np. z lampy cofania. The next step is to connect the car charger and both plugs into the navigation. When properly connected, the camera image will automatically appear on the screen when the transmitter is powered up.

The 4366/5066/7066 series are based on MediaTek 3351 solutions with 468MHz processors.

If your device after start for a while shows the navigation menu, and then automatically switches to a map, you should select exit in the menu options to bring up the navigation menu. If you would like to make your device does not automatically run map, go to SETTINGS->MAP PATHS and uncheck the automatic start of the program.

GoClever navigation devices have a multimedia player that supports the following file types: WMA, WMV, JPG, BMP and PNG. Devices have an e-book reader that reads text files in TXT file format only.

a) device is working on battery, no charger plugged in: - LED is not lit
b) device is plugged to charger, battery is charging: - LED is red
c) device is plugged to charger, battery is fully charged: - LED is blue
Additionally, in this series device that is turned off and battery is charging, the screen displays information about battery charge level.

In order to run other programs on your device, go to SETTINGS -> MAP PATHS, and then select specified program.
After performing this operation, selected program should start. If you want to start the navigation program, similar steps should be performed by selecting the following program "media :\mobilenavigator\ mobilenavigator.exe"

To connect the 5066 / 5065 device with mobile phone via Bluetooth, take the following steps:
1. Please check that Bluetooth is on. To do this click on "BLUETOOTH-> SETTINGS" and check BT icon in the upper right corner of the screen that should be behind the red circle crossed out ( GPS )
2. Please turn on Bluetooth in your mobile phone ( MP )
3. Please search for your navigation device in mobile phone ( MP )
4. Please connect both devices by entering a default password „0000” on your mobile phone ( MP )
5. The information about connection should appear in navigation device, click OK ( GPS )
6. Allow access to mobile phone's files for your navigation device ( MP )
7. If everything is done correctly, the device will be synchronized with your mobile phone and will automatically connect with it in the future.

WARNING! If you want to import text messages and address book from your mobile phone, you must insert a memory card to your navigation device first.

LEGEND
MP – MOBILE PHONE
GPS – NAVIGATION DEVICE

Please check the following list:
"http://download.gocelver.net/manuals/xx66_compactible_phone_list.pdf "

Yes. When viewing an image, click on the screen corners in order to adjust the screen display to your preferences.

GPS receiver works on COM1 port at 57600.

The 4366/5066/7066 series are based on MediaTek 3351 solutions with 468MHz processors.

The 3540/4340/5040 series are based on Mstar solutions with 400MHz processors.

To connect the back camera, connect the camera with transmitter, then connect the power cables to 12V power source (for example from backup light).
The next step is to connect the car charger and both plugs into the navigation. When properly connected, the camera image will automatically appear on the screen when the transmitter is powered up.

You can use micro SD HC cards up to 8GB for NAVIO, xx66 and xx40. The older types of navigation devices are compatible with class IV SD cards up to 4GB.

All GPS Goclever devices can be charged with 5V chargers with current intensity 1 - 1.5A, except for the devices with video cameras which should be charged with chargers with current intensity 2 - 3A.
Navigation devices should be charged up to 12 hours for full charge level.

Devices NAVIO, xx66, xx40 can be charged via the USB port, but due to the low current intensity (about 0.3 to 0.5A) it can take up to several times longer than charging with correct charger.
In the case when the current consumption level is too high, your device may not charge at all, so if you must charge the device via the USB port, it is recommended to disable navigation device while charging.

ABSOLUTELY NO! The intensity of current required to charge the mobile phone is significantly lower than those needed to operate the navigation device, so the charger will not have enough power to recharge the device, in critical cases, it may be too small intensity to the device to work properly, which can lead to malfunction and even damaging your navigation device.

The GPS receiver must receive signals from at least 3 satellites to be able to calculate your location. In some cases, the initial position calculation can take up to 10 minutes, especially if you move at high speed. This process can significantly speed up if you stop at a place where nothing obscures the sky.
In addition, waiting time for the calculation of your starting position depends on many factors:
1. Time and distance from the point where the GPS receiver has been activated in the last time.
2. Obstruction of the sky by various objects.
3. Your current speed.
4. The current location of the satellites.
Calculate your location may not be possible if you are in a building, tunnel or very close to a high building.

The Global Positioning System (GPS) is a space-based satellite navigation system that provides location and time information in all weather, anywhere on or near the Earth, where there is an unobstructed line of sight to four or more GPS satellites. It is maintained by the United States government and is freely accessible by anyone with a GPS receiver. The system imposes some technical limitations which are only removed for authorized users.

For more information see:
http://en.wikipedia.org/wiki/Global_Positioning_System
Source:
http://en.wikipedia.org/

If you navigation any device model imprecisely indicates the place where you touching the screen,If you must calibrate your device. Calibration is in the navigation settings menu. Calibration is to click on the screen five times in the center of small crosshair. If you don't do it within 30 seconds time limit, the calibration will be aborted.

FM Transmitter in Goclever devices transmits an FM signal that can be received in a free band on the radio receiver. Devices where in model name is FM and NAVIO Plus.

Navigation xx40, xx66, NAVIO devices can be connected to a PC via a USB cable, depending on model and software version.
You can choose USB MASS STORAGE mode or ACTIVESYNC mode.
You can choose one of these modes by accessing USB settings menu in your navigation device. The USB Mass Storage mode: the operating system automatically detects your device as a removable drive (or as a SD card and internal memory).
To connect the device with ACTIVESYNC, you must install the Active Sync software on your PC (for Windows XP users) or Windows Mobile Device Center (for Windows Vista and Windows 7 users).

No, FM Transmitter can only transmit the signal.

If your device after start for a while shows the navigation menu, and then automatically switches to a map, you should select exit in the menu options to bring up the navigation menu.
If you would like to make your device does not automatically run map, go to SETTINGS->MAP PATHS and uncheck the automatic start of the program.